This free ESP32 GPIO pin picker tells you which pins on an ESP32, ESP32-S3, ESP32-C3 or ESP32-C6 are safe for a relay, a button, an I2C bus, an analog sensor or a deep-sleep wake button, and which ones will bite you at boot. Pick the chip and what you need the pin for, and every GPIO comes back ranked from safe to avoid, each with a one-line reason.
Pinout diagrams show what a pin can do, not what it can break. Third-party pinout articles also disagree with each other, for example on which ESP32-C6 pins are strapping pins. So this ESP32 GPIO pin picker takes its data from Espressif’s own datasheets and the ESP-IDF reference, and checks it against the pin validation in ESPHome’s source code.
What This ESP32 GPIO Pin Picker Does
- 🧭 Ranks every GPIO for your use. Choose digital I/O, digital input, I2C, SPI, UART, PWM, ADC, touch, deep-sleep wake or DAC, and the best pins come first: safe, then use with care, then avoid.
- 🥾 Explains strapping pins. Each strapping pin shows what it straps (boot mode, flash voltage, boot log, JTAG source) and the level it needs at reset, so you can see why GPIO12 on the original ESP32 can stop a board from booting.
- 💾 Knows your module. Flash and PSRAM pins change with the module: PSRAM takes GPIO16 and GPIO17 on WROVER-type ESP32 modules, octal PSRAM takes GPIO33 to GPIO37 on the ESP32-S3, and some ESP32-C3 and ESP32-C6 variants don’t bond out certain pins at all. Not sure what you have? The default assumes the strictest case.
- 📈 Gets ADC2 right for each chip. On the original ESP32, ADC2 can’t be read while Wi-Fi is on. On the ESP32-S3 it shares access with Wi-Fi, ESP-IDF no longer supports ADC2 one-shot reads on the ESP32-C3, and the ESP32-C6 has no ADC2 at all. A Wi-Fi switch updates the verdicts.
- 🏷️ Flags everything else that matters: input-only pins, USB D- and D+, UART0 TX and RX, pad JTAG, touch channels, RTC and LP pins that can wake the chip, the ESP32 DAC, power-up glitches and the 32 kHz crystal pins.
- ✅ Cross-checks ESPHome. For the selected pin you see whether ESPHome 2026.10.0 accepts it, warns or refuses it, and you can copy a ready ESPHome snippet for that pin.
- 🔗 Shares the result. The chip, module, use, Wi-Fi setting and pin live in the URL, so a link shows exactly what you saw.
How to Use the ESP32 GPIO Pin Picker
- Pick the chip: ESP32, ESP32-S3, ESP32-C3 or ESP32-C6.
- Select your module, chip variant or package if you know it, and untick Wi-Fi only if your firmware never turns it on.
- Choose what the pin is for. The ESP32 GPIO pin picker re-sorts the list with the best pins at the top.
- Click a pin to see every reason behind its verdict, its boot strapping details and what ESPHome says about it.
- Copy the ESPHome snippet and paste it into your device’s YAML.
How the ESP32 GPIO Pin Picker Decides
The verdicts follow the datasheets’ own pin priorities. Pins the datasheet lists as free to use are safe. Pins it says to use with caution, such as strapping, USB, JTAG and UART0 pins, are marked use with care. Flash, PSRAM and flash supply pins are avoid. Within each group the pins with the mildest side effects come first.
Where Espressif’s documents and ESPHome disagree, the ESP32 GPIO pin picker shows the stricter verdict and says why. Two examples: ESPHome doesn’t warn about GPIO11 on the ESP32-C3, but the datasheet calls it the flash supply pin, so it is marked avoid. And ESPHome accepts an ADC sensor on GPIO5 of the ESP32-C3, while ESP-IDF says ADC2 readings on that chip are not stable.
Keep in mind that the ESP32 GPIO pin picker works with chip-level data. A dev board can wire any pin to a BOOT button, an LED, a USB-UART bridge or a display, and a module may not lead every pin out, so check your board’s schematic before you solder.
Practical Use Cases
A few ways to put the ESP32 GPIO pin picker to work:
- 🔌 Relays and buttons. Find outputs that don’t toggle during boot, and inputs that won’t drop the chip into download mode when the button is held at reset.
- 🌡️ Analog sensors. Pick an ADC1 pin that keeps working with Wi-Fi on, for a soil moisture probe or the water quality sensor in my reverse osmosis TDS and flow meter on an ESP32-C6.
- 🖥️ Touchscreen projects. Display, touch and I2C lines use up pins quickly on an ESP32-S3. Check what is left before you add a sensor, as with my touch-controlled Home Assistant dashboard and an ESPHome media controller with an LVGL screen.
- 🔋 Battery sensors. Find the RTC or LP pins that can wake the chip from deep sleep, so a door contact or a button can end the nap early.
- 🛒 Choosing hardware. Compare the free pins of each chip before you buy, next to my notes on which ESP32 version to use in 2026 and the best ESP32 dev boards.
Privacy, Ads, and Data Policy
- ✅ 100% free: no registration and no limits.
- ✅ No data storage: the ESP32 GPIO pin picker saves nothing. Your choices live only in the page URL.
- ✅ No ads in results: no watermarks or tracking in the snippets you copy.
- ✅ Client-side only: no external requests and no libraries; all the pin data ships with the page.
Open Source and Self-Hosting
The ESP32 GPIO pin picker is open source on GitHub: three files (index.html, style.css and script.js) with no dependencies, which you can drop onto any static web server, the same way I host IT-Tools on my home server. Every pin fact in script.js names its source document and version, and the unit tests compare the data with tables transcribed from the datasheets and with ESPHome’s own pin lists, so a correction is easy to verify.
Like the ESP32 GPIO pin picker, every tool on the Tools page runs in your browser, for example the YAML, JSON and TOML Converter for checking a config snippet.
Built by VahaC — 100% client-side, no data sent anywhere.
